How To Identify
Your Saltwater 5000 Round Pool Components

Learn how to identify the different components of your Saltwater 5000 Round Pool.

Saltwater 5000 Round Pool Model

Parts Breakdown

Identifying the parts of your pool model before you begin your installation will make the process of assembling the swimming pool much easier. Below you will find a complete breakdown of the parts and components for the Saltwater 5000 Round Swimming Pool Model.

Top Rail – Reference #6

Top Rail

The Top Ledges (sometimes referred to as Top Rails) are the top finishing components of the swimming pool that are placed between the vertical upright posts. The Top Ledges are 7″ wide and are located at the very top of your pool.

Material: Resin

Ref #	Description	Part #	Length	15'	18'	21'	24'	27'	30'
6	Top Ledge	22774	56-3/16"	10	12	14	16	18	20

Inner Stabilizer – Reference #1

Inner Stabilizer

The Inner Stabilizers (sometimes referred to as Top Track Stabilizers) are the tracks that stabilize the top of the pool wall.

Material: Resin

Ref #	Description	Part #	Length	15'	18'	21'	24'	27'	30'
1	Top Track (Inner Stabilizer)	29889	56-1/16"	10
		29890	56-1/16"		12
		29891	56-1/16"			14
		29892	56-1/16"				16
		29894	56-1/16"					18	20

Top Caps – Reference #9 & #10

Top Cover/Outer Cap for Cameo, Heritage RTL, Signature RTL & Saltwater 5000 - Round & Oval Curved End

Top Cap/Outer Cap

Top Cover/Inner Cap for Cameo, Heritage RTL, Signature RTL & Saltwater 5000

Top Cap/Inner Cap

The Top Caps consist of (2) parts. There is a Top Cover/Outer Cap which is closer to the outside of the pool. The Top Cover/Inner Cap is installed on the inside of the swimming pool closer to the water. The Top Caps cover all of the hardware where your Top Ledges screw into the Top Joiner Plates.

Ref #	Description	Part #	15'	18'	21'	24'	27'	30'
9	Top Cover/Inner Cap	22732	10	12	14	16	18	20
10	Top Cover/Outer Cap	22734	10	12	14	16	18	20

Top Plates – Reference #3 & #13

pool-supplies_replacement-parts-650x650-00009-dm_1125x1125.webp__PID:9a03d851-395e-4b56-b751-c8296cdb62e1

Top Plate Curved Side

The Top Plates are screwed in at the top of every Upright. Your swimming pool’s Top Ledges will be screwed into these Top Plates.

Material: Resin

Ref #	Description	Part #	15'	18'	21'	24'	27'	30'
3	Top Joiner Plate	38908	10	12	14	16	18	20

Uprights – Reference #5 & #14

Upright

The Uprights are the vertical posts on the outside of your swimming pool wall. Each upright post inserts into the bottom resin boots and connects to the top joiner plate with screws.

Ref #	Description	Part #	Length	15'	18'	21'	24'	27'	30'
5	Upright	22759	51-5/8"	10	12	14	16	18	20

Upright Boot – Reference #8

Boot

The Upright Boots connect your Bottom Tracks together. Your uprights will also clip into the Upright Boots.

Ref #	Description	Part #	15'	18'	21'	24'	27'	30'
8	Upright Boot	22735	10	12	14	16	18	20

Coping Strips – Reference #7

Coping For Overlap Liners - 2ft. Section

Coping Strips

Overlap Liner Installation Using Coping Strips

An Overlap Pool Liner is installed by overlapping it over the pool wall and using plastic Coping Strips to hold it in place. Coping Strips are not required when installing a Uni-Bead Liner or J-Hook Liner, but they are included with the swimming pool. If using a Uni-Bead or J-Hook liner you can discard the coping strips.

Ref #	Description	Part #	Length	15'	18'	21'	24'	27'	30'
7	Coping Strips	10296	48"	12	14	16	19	21	24

Bottom Track – Reference #2

Bottom Track

The Bottom Track (sometimes referred to as Bottom Rail) is where your pool wall sits.

The Bottom Tracks insert into the Upright Boots on the bottom of the swimming pool.