How To Identify Your
Tribeca Oval Pool Components

Learn how to identify the different components of your Tribeca Oval Pool.

Tribeca Oval Pool Model

Parts Breakdown

Identifying the parts of your swimming pool before the installation process will make the installation a lot easier and go more smoothly. Below you will find a breakdown of the parts that are used on our Tribeca Oval Above Ground swimming pool and where they are used and installed.

Top Ledge – Index I

Top Ledge

The Top Ledges (sometimes referred to as Top Rails) are the top finishing components of the swimming pool that are placed between the vertical upright posts. The Top Ledges are 7″ wide and are located at the very top of your pool.

Ref #	Description	Part #	Length	15'x26'	15'x30'	18'x33'	18'x40'
I	Top Ledge (Straight Section)	40356	40"	8	10	10	14
	Top Ledge (Round Section)	40353	49-1/2"	10	10
	Top Ledge (Round Section)	40354	51-1/8"			12	12

Top Track – Index J

Top Track

The Top Tracks (sometimes referred to as Stabilizers) are the tracks that stabilize the top of the pool wall.

Ref #	Description	Part #	Length	15'x26'	15'x30'	18'x33'	18'x40'
J	Top Track (Straight Section)	38512	33"	4	6	6	10
	Top Track (Transition Section)	38511	37"	4	4	4	4
	Top Track (Round Section)	38502	53-1/4"	10	10
	Top Track (Round Section)	38503	54-1/8"			12	12

Ledge Cover Inner/Outer – Reference B & C

Top Cap/Inner Ledge Cover for & Tribeca Pool ModelsPreference

Ledge Cover Inner

Top Cap/Outer Ledge Cover for Preference & Tribeca Pool Models

Ledge Cover Outer

The Ledge Covers consists of (2) parts. There is a Ledge Cover Inner which goes towards the inside of the pool. The Ledge Cover Outer will go towards the outside of the pool.

The Ledge Covers cover all of the hardware where your Top Ledges screw into the Top Plates.

Ref #	Description	Part #	15'x26'	15'x30'	18'x33'	18'x40'
B	Ledge Cover Inner	22121	18	20	22	26
C	Ledge Cover Outer	22120	18	20	22	26

Ledge Cover Top – Reference A

Ledge Cover Top

The Ledge Cover Tops are installed on top of the Ledge Cover Outer.

Ref #	Description	Part #	15'x26'	15'x30'	18'x33'	18'x40'
A	Ledge Cover Top	22122	18	20	22	26

Top Plate – Reference D

Top Joiner Plate for Round & Oval Curved Side Preference & Tribeca Pool Models

Top Plate

The Top Plates are screwed in at the top of every Upright. Your swimming pool’s Top Ledges will be screwed into these Top Plates.

Ref #	Description	Part #	15'x26'	15'x30'	18'x33'	18'x40'
D	Top Plate	38488	18	20	22	26

Uprights – Index E & F

Inner Upright

Outer Upright

The Inner Uprights are the vertical posts on the outside of your swimming pool wall. Each Inner Upright connects to the Foot Covers (Boot).

The Outer Uprights are the vertical posts that cover your Inner Uprights. Each Outer Upright connects to the Foot Covers (Boot).

Ref #	Description	Part #	15'x26'	15'x30'	18'x33'	18'x40'
E	Inner Upright	22132	18	20	22	26
F	Outer Upright	22130	18	20	22	26

Foot Cover (Boot) – Reference G

Bottom Joiner Plate/Upright Boot for Curved Side Preference & Tribeca Pool Models

Foot Cover Round Section

Upright Boot/Bottom Joiner Plate for Straight Side Preference/Tribeca Pool Model

Foot Cover Straight Section

The Foot Covers connect your Bottom Tracks together. Your Uprights will also clip into these Foot Covers.

Ref #	Description	Part #	15'x26'	15'x30'	18'x33'	18'x40'
G	Foot Cover Round Section	22123	12	12	14	14
	Foot Cover Straight Section	22124	6	8	8	12

Upright Channel – Index 1

Upright Channel

The Upright Channel is the vertical post on the straight section of the oval pool. It attaches to the Base U-Channel using the "T" and "L" Brackets.

Ref #	Description	Part #	15'x26'	15'x30'	18'x33'	18'x40'
1	Upright Channel	1440383	6	8	8	12

Brackets - Index 2, 3 & 4

Outside ‘T’ Bracket

Middle ‘T’ Bracket

Inside ‘L’ Bracket

The "T" and "L" Brackets connect to the Upright Channel and Base U-Channel.

Ref #	Description	Part #	15'x26'	15'x30'	18'x33'	18'x40'
2	Outside ‘T’ Bracket	1320139	12	16	16	24
3	Middle ‘T’ Bracket	1320138	12	16	16	24
4	Inside ‘L’ Bracket	1320147	12	16	16	24

Base U-Channel – Index 7

Base U-Channel

The Base U-Channels are located on the straight section of the oval pool.

This is where your Upright Channel, "T" and "L" Brackets, Strap Brackets, and Hold Down Plates are attached.

Ref #	Description	Part #	15'x26'	15'x30'	18'x33'	18'x40'
7	Base U-Channel	1440335	6	8	8	12

Hold Down Plate (Pressure Plate) – Index 11

Hold Down Plate

The Pressure Plates are corrugated steel plates that attach to the Base U-Channels.

Ref #	Description	Part #	15'x26'	15'x30'	18'x33'	18'x40'
11	Hold Down Plate	1320166	12	16	16	24

Bottom Rail – Index K

Bottom Rail

The Bottom Rail (sometimes referred to as Bottom Track) is where your pool wall sits.

The Bottom Rail inserts into the Foot Covers.

Ref #	Description	Part #	Length	15'x26'	15'x30'	18'x33'	18'x40'
K	Bottom Rail (Straight Section)	16713	37-1/2"	4	6	6	10
	Bottom Rail (Transition Section)	16714	39"	4	4	4	4
	Bottom Rail (Round Section)	14950	49"	10	10
	Bottom Rail (Round Section)	14949	50"			12	12

Strap – Index 8

Strap

The Straps are connected to the Strap Brackets and lay flat across the width of our Oval Swimming Pools.

Ref #	Description	Part #	15'x26'	15'x30'	18'x33'	18'x40'
8	Strap 15’	22095	9	12
	Strap 18'	22096			12	18

Strap Bracket – Index 30

Strap Bracket

The Strap Brackets attach to your Base U-Channels.

This is where your Straps are connected.

Ref #	Description	Part #	15'x26'	15'x30'	18'x33'	18'x40'
30	Strap Bracket	1320164	6	8	8	12

Coping Strips – Only Included with Overlap Liners

Coping For Overlap Liners - 2ft. Section

Coping Strips

Overlap Liner Installation Using Coping Strips

An Overlap Pool Liner is installed by overlapping it over the pool wall and using plastic Coping Strips to hold it in place. Coping Strips are not required when installing a Uni-Bead Liner or J-Hook Liner.