Installing a Pool with a Sand Base, Foam Cove and Liner Floor Pad
It's time to install that Swimming Pool and it's essential that its done correctly using a sand base, foam cove and liner floor pad.
Many do-it-yourselfers installing an above ground swimming pool for the first time have questions regarding how to properly install a swimming pool with a sand base, foam cove and liner floor pad.
This article will illustrate the correct way to accomplish this in order to make the installation go smoother and protect the pool liner and pool wall from being damaged.
The information in this article is provided and referenced directly from each swimming pool manufacturer’s installation and safety instruction manual (Wilbar International, Trendium Pool Products and Trevi).
Wilbar International, Trendium Pool Products and Trevi Swimming Pool Installation & Safety Instruction Manuals can be found by clicking on the link for each specific pool model below:
- Bristol Pool Model
- Boreal Pool Model
- Cameo Pool Model
- Daytona Pool Model
- Hampton Pool Model
- Intrepid Pool Model
- Melenia Pool Model
- Saltwater 5000 Pool Model
- Quest Pool Model
- Saltwater 8000 Pool Model
- Saltwater LX Pool Model
- Saltwater Aurora Pool Model
- Signature RTL Pool Model
- Tribeca Pool Model
One of the biggest problems that we see is with the height of the base beneath the above ground pool liner. When the sand base is not high enough there is excess strain put on the pool liner and pool wall, and this tremendous weight of the water can easily cause the vinyl pool liner to “blowout” and/or the metal pool wall to be pulled down.
Above ground pool liners are not built to withstand water weight, they are simply made to line the inside of a pool to hold the water. Therefore, when installing a new above ground swimming pool or a new above ground pool liner it is extremely important to make sure that the vinyl pool liner is supported by the proper base. There should be NO AIR SPACE between the vinyl pool liner and the base that it should be resting on.
Avoid Air Pockets During Liner Installation
View the diagram’s below to see how the CORRECT and INCORRECT ways to install your pool liner.
Installation Instructions
Step 1
Using fine sand (free of rocks and debris), lay a 3″ thick bed of sand across the entire inside of the pool (wall-to-wall) this will form your base.
Step 2
After installing the 3″ sand base, lay the liner floor pad on top. Please note your liner floor pad is pre-cut to fit your pool’s exact dimensions.
Step 3
Attach the pool cove (foam) directly on top of the liner floor pad by removing the adhesive backing and sticking it to the metal pool wall (where the liner floor pad meets the metal pool wall).
Step 4
This is the completed above ground pool liner installation. The vinyl pool liner should be completely supported by the pool base to avoid any stress or damage to it or the metal pool wall.
Above Ground Pool Installation Items
The following are links to various sections on our website ThePoolFactory.com where you can select pool liner installation items based off your above ground pool size.
Pool Cove (Foam)
Pool Cove is foam that easily peels and sticks to the inside base of the pool wall. The foam pool cove is 3-3/4 inches high and must be installed on top of 3 inches of sand. This will give you a total height of about 7 inches, the recommended height to support the liner and eliminate stress at the seam of the pool liner.
Shop ProductsArmor Shield Liner Floor Pad
Armor Shield Floor Pad provides an important protective layer between a vinyl swimming pool liner and it’s sand base. Unlike traditional foam padding, Armor Shield is a Polypropylene Geotextile material that prevents cuts and punctures to vinyl liners caused by rocks, roots, grass and even glass!
Shop ProductsWhile shopping on our website if you have any questions about any of the products or sizes that you may need please don’t hesitate to contact us via Live Chat or our contact us form.
How Much Sand Will I Need For Pool Installation?
Table header 0 | Table header 1 | Amount for Sand Base with SAND COVE | Table header 3 | Amount for Sand Base with FOAM COVE |
---|---|---|---|---|
Pool Size | Yards of Sand | Tons of Sand | Yards of Sand | Tons of Sand |
12' Round | 1.00 | 1.40 | 0.75 | 1.00 |
15' Round | 1.50 | 2.00 | 1.00 | 1.50 |
18' Round | 2.00 | 3.00 | 1.50 | 2.00 |
21' Round | 2.50 | 3.50 | 2.00 | 2.50 |
24' Round | 3.50 | 5.00 | 2.50 | 3.50 |
27' Round | 4.00 | 5.50 | 3.00 | 4.00 |
30' Round | 5.50 | 7.75 | 4.00 | 5.75 |
33' Round | 7.00 | 10.00 | 5.25 | 7.50 |
8' X 12' Oval | 0.75 | 1.00 | 0.50 | 0.75 |
8' X 14' Oval | 1.00 | 1.40 | 0.75 | 1.05 |
8' X 15' Oval | 1.00 | 1.40 | 0.75 | 1.05 |
8' X 16' Oval | 1.00 | 1.40 | 0.75 | 1.05 |
8' X 19' Oval | 1.00 | 1.40 | 0.75 | 1.05 |
10' X 15' Oval | 1.00 | 1.40 | 0.75 | 1.05 |
10' X 16' Oval | 1.00 | 1.40 | 0.75 | 1.05 |
10' X 18' Oval | 1.25 | 1.75 | 1.00 | 1.40 |
10' X 19' Oval | 1.25 | 1.75 | 1.00 | 1.40 |
10' X 21' Oval | 1.50 | 2.00 | 1.25 | 1.75 |
12' X 16' Oval | 1.25 | 1.75 | 1.00 | 1.40 |
12' X 17' Oval | 1.50 | 2.00 | 1.00 | 1.40 |
12' X 18' Oval | 1.50 | 2.00 | 1.00 | 1.40 |
12' X 20' Oval | 1.75 | 2.50 | 1.25 | 1.75 |
12' X 21' Oval | 1.75 | 2.50 | 1.25 | 1.75 |
12' X 24' Oval | 2.00 | 3.00 | 1.50 | 2.00 |
12' X 27' Oval | 2.50 | 3.50 | 2.00 | 3.00 |
14' X 20' Oval | 2.00 | 3.00 | 1.50 | 2.00 |
15' X 23' Oval | 2.50 | 3.50 | 1.75 | 2.50 |
15' X 24' Oval | 2.50 | 3.50 | 1.75 | 2.50 |
15' X 26' Oval | 2.75 | 4.00 | 2.00 | 2.75 |
15' X 30' Oval | 3.50 | 5.00 | 2.50 | 3.50 |
16' X 26' Oval | 3.50 | 5.00 | 2.50 | 3.50 |
16' X 32' Oval | 4.00 | 5.50 | 3.00 | 4.00 |
18' X 33' Oval | 4.50 | 6.50 | 3.50 | 4.50 |
18' X 40' Oval | 5.50 | 7.50 | 4.5 | 6.00 |
21' X 43' Oval | 7.00 | 10.00 | 5.25 | 7.50 |